Home Sewing - How to Make Yours Not Look Homemade
Posted: Monday, April 02, 2007
by Thelma Horton
Sew-It Yourself
Most of us will agree that sewing your own clothes saves you money and brings much satisfaction. It is gratifying when you complete a project and can say that you sewed it yourself. But, perhaps the biggest reason most people do not sew their own clothes is because they look homemade. You start out with visions that the outfit will look exactly on you the way it looked on the pattern envelope, but when it’s finished it looks like something is missing. And, you can’t quite put your finger on what it is.
What I learned in that sewing class was that the secret to making home sewing not look homemade was in the press…using those odd looking sewing tools. I didn’t know that if I put off pressing the garment until completion, that it would be too late to set in the shape. I didn’t know that no matter how well I sewed, the professional look was also a result of proper pressing.
Yes, properly pressing seams as you sew actually shapes the garment and sets the stitching lines. As we all know, the body is not flat, it has curves, and using the ironing board alone will not shape the garment properly. The only way to shape your garment is by using the proper pressing equipment along with the ironing board.
If you are like me, and most home sewers, before taking a sewing class, you are also unfamiliar with specialized pressing equipment and not accustomed to using them. But, using the proper tools along with the proper pressing and sewing techniques makes the difference in the end result. It helps shape the fabric so it will fit the body more smoothly. Some of those odd looking pressing tools are listed below:
- Steam iron for pressing and shaping fabric and setting stitches at all stages of construction.
- Ironing board, well padded and smoothly covered in 100% cotton cover, absorbs moisture from the steam iron.
- Tailor’s ham for pressing shaped areas and curved seams.
- Seam roll, or sleeve roll, for pressing seam allowances open and pressing seams in narrow areas.
- Clapper for pressing sharp creases without it looking over-pressed.
- Wooden point presser for pressing corners and points, and pressing straight seams open.
- Press cloths for protecting the right side of the fabric during pressing.
Ironing board covers should be 100% cotton because the all cotton fabric absorbs the moisture so that the fashion fabric will dry quickly. The traditional ironing covers with the reflective surface, actually reflects the steam, and may cause burn damage to some fabrics and slows down the drying process when you’re shaping with steam.
First, be sure you know the fabric content to determine the proper heat setting for the iron, then follow the techniques below as you sew your garment pieces together.
Press curved areas such as darts, hiplines, bustlines and collars over the tailor’s ham from the wrong side with the point of the dart smoothed flat over the end of the ham to shape their curve. Horizontal darts should be pressed down, and vertical darts should be pressed toward the center of the garment.
Curved seams sometimes need to be clipped slightly along the edges so they can be pressed open without puckering. Do not clip any closer to the seam than absolutely necessary to press the seam flat. Be careful not to cut pass the stitched seam.
Darts in heavy or bulky fabric will be less bulky if you slash, and then press open. Be careful not to slash so close to the point that the fabric will pull apart.
Press seams open over sleeve or seam roll from the wrong side with the tip of the iron along the stitching line to prevent the seam edges from marking or showing through on the right side.
Follow the grain line in the fabric when pressing by moving the iron in the same direction as the lengthwise yarns of the fabric. Pressing across the grain or on the bias can stretch the garment piece out of shape.
Following the above pressing and sewing techniques will help you achieve the professional-looking results every home sewer dreams of. So, instead of a homemade looking garment, proper pressing gives you professional results and garments that you’ll be proud to say… “I sewed it myself."
Thelma Horton has a degree in Home Economics, and has taught hundreds of high school students and adults how to sew for the very first time. She has also sewn prom & wedding dresses, tailored suits and coats and altered ready-to-wear for her clients. To help others learn how to sew, she offers free tips and techniques on her website at http://www.sew-it-yourself.com and authors two e-books, "Sew-It Like a Pro" and "Hem-It Yourself, Hem Finishes."
This Article has been viewed 363 times. (Not updated in real-time.)
Top-level comments on this article: (1 total)please correct the word "ham" to hem.Thanks for allowing me to clarify the statement, "Press curved areas such as darts, hiplines, bustlines and collars over the tailor’s ham from the wrong side with the point of the dart smoothed flat over the end of the ham to shape their curve." Here, when shaping darts or other curved areas, we are actually placing the dart over the end of the tailor's ham. Then, allowing the steam from the iron to set the shape of the bust area. So, the word "ham" is correct.
We want your comments! If you can read this, you don't have javascript enabled, so you can't use this comment system. Please enable javascript.